Question 1

ERA-DCRX 12V Output Wiring: Wire Distance & Multiple Strobes

Accepted Answer

Learn how to wire 12V strobes to the ERA-DCRX receiver, compare estimated wire distances, and plan multiple accessories within the 900 mA combined limit across all four 12V DC outputs.

Question 2

Powering Your Safeguard Supply Receiver at Home or Abroad

Accepted Answer

Choose a replacement adapter by the exact receiver model. The ERA-RXPG uses a documented 5V DC supply, while the ERA-DCRX uses a documented 12V DC supply. Check voltage, current, connector dimensions, and polarity against the receiver documentation before plugging in a replacement, even when two adapters share the same voltage.

Question 3

Doorbell Wire Extender: Hear a Wired Doorbell Farther Away

Accepted Answer

A doorbell wire extender connects to your existing wired doorbell and sends its signal wirelessly to a receiver elsewhere, with no new wire to run.

Question 4

What is the ERA-UTDCR Wireless Door Alert System?

Accepted Answer

The ERA-UTDCR is a wireless entry alert kit that pairs an ERA-UTX transmitter with an ERA-DCRX receiver. Use the transmitter as a push button or a door contact, depending on how you want to trigger the alert. Test the receiver from the intended entrance before permanently mounting the transmitter.

Question 5

What is a doorbell wire extension kit?

Accepted Answer

A doorbell wire extension kit lets you lengthen the wiring between components of an existing wired doorbell system. Check whether the kit includes the wire and connectors needed for your installation, then compare the wire requirements and planned run with the instructions for your button, chime, and transformer.

Question 6

How to Extend a Wired Doorbell Chime or Button Wire

Accepted Answer

To place a wired doorbell component farther from the others, check the wiring requirements for the button, chime, and transformer before extending the cable. Measure the proposed run and choose compatible wire and connectors. Turn off power before changing any wiring, then test the chime after restoring power.

Question 7

How to Install a Wired Doorbell

Accepted Answer

We found a great video that demonstrates how to install a wired doorbell. Please note, 1800doorbell.com did not produce this video and is not responsible for its content.

Question 8

How to Install a Wired Doorbell Button

Accepted Answer

Installing a wired doorbell button may seem daunting, but once you understand the fundamentals, it is usually a simple low-voltage replacement.

Question 9

How to Replace a Wired Doorbell Push Button

Accepted Answer

Replace an older wired doorbell button or update the button style by safely disconnecting the low-voltage wires and installing a compatible replacement.

Question 10

How to Wire Two Door Chimes to One Doorbell Transformer: Complete Guide

Accepted Answer

Learn expert doorbell wiring techniques to connect two chimes to one transformer. Step-by-step guide with essential safety tips and wiring diagrams for home installation.

Question 11

Troubleshooting a Wired Doorbell

Accepted Answer

Chimes consist of a wired push button, a wired chime sound device, and a transformer that changes household voltage to low-voltage doorbell power.

Question 12

Troubleshooting Craftmade Wired Doorbells & Push Buttons

Accepted Answer

Chimes consist of a push button, a chime sound device, and a transformer that changes household voltage from 120 volts to low-voltage doorbell power.

Question 13

What's the Difference Between Wired Push Button Mounting Styles

Accepted Answer

Flush mount, recessed, and surface mounted wired doorbell buttons differ by how the button housing sits against the wall, trim, or electrical box.

Question 14

Product Manuals

Accepted Answer

Documentation library for Safeguard Supply wireless doorbell, alarm, and alert system products including LRA, ERA, and SS series devices with downloadable user manuals.

Question 15

Extending ERA System Range Using Signal Relay Technology

Accepted Answer

Create a signal relay system using the ERA-UTX and ERA-DCRX's C-FORM relay to double your wireless alert system's range, extending coverage up to 8,000 ft while eliminating interference.

Question 16

Product User Manual: LRA-D1000S-L Doorbell Kit

Accepted Answer

The LRA-D1000S is a wireless door chime comprising the LRA-PBTXA-L wireless push button transmitter and LRA-DCRXSA-L receiver. This manual covers battery installation, pairing, and mounting procedures.

Question 17

ERA-PBTX Push Button User Manual

Accepted Answer

Pair the ERA-PBTX wireless push button with an ERA-compatible receiver using the instructions for that receiver model. Install the battery as shown in the manual, complete pairing, and test the alert from the intended mounting position before securing the button. Follow the manual’s coin battery warnings when servicing it.

Question 18

ERA-RXPG Plugin Receiver User Manual

Accepted Answer

The ERA-RXPG is a long-range wireless door chime receiver that plugs into a standard 120V outlet. It supports 12 melodies, three operational modes, and up to 12 programmed transmitters.

Question 19

Programming Guide: How to Set Up ERA-PIR Motion Sensor with ERA-DCRX Receiver

Accepted Answer

Step-by-step guide for programming your ERA-PIR motion sensor to ERA-DCRX receiver. Learn zone setup, custom tones, and optimization tips for your wireless alert system.

Question 20

ERA-DCKIT Wireless Doorbell Kit User Manual

Accepted Answer

Setup instructions for the ERA-DCKIT wireless door chime kit, which includes the ERA-RXPG plugin receiver and ERA-PBTX wireless doorbell push button.

Question 21

Programming the SS130 Door Alert Kit by Safeguard Supply

Accepted Answer

To pair the SS130 door sensor, select the melody on the SS135 receiver first. Hold the volume button for five seconds until the receiver sounds and its LED flashes. Activate the sensor while the LED is flashing, then open the door to confirm that the receiver plays the selected melody.

Question 22

Connect DB-2000 Bell to ERA-DCRX Receiver for Enhanced Alert Volume

Accepted Answer

Connect a DB-2000 bell to your ERA-DCRX receiver for enhanced sound output in noisy commercial environments. The ERA-DCRX delivers 95 dBA at 5 feet and supports various 12V DC alerting devices.

Question 23

How to Clear Event Logs on Your ERA-VPRX Receiver

Accepted Answer

The ERA-VPRX receiver stores up to 200 events per zone. This guide explains how to view and clear event logs when needed.

Question 24

WDK-ERA-STROBE: Professional Wireless Alert System with Visual Notification

Accepted Answer

A professional wireless alert system combining 4,000-foot range with strobe light notifications, expandable for commercial environments.

Question 25

ERA-UTX Installation Guide: Push Button and Door Contact Mounting Instructions

Accepted Answer

Step-by-step instructions for mounting your ERA-UTX as a push button or door/window contact.

Question 26

RED LED Indicator Lights on the LRA-DCRXS Plug-In Receiver

Accepted Answer

The red LED on the LRA-DCRXS receiver indicates low battery during normal operation and shows zone status during programming mode.

Question 27

How to Replace the Battery in the LRA-PBTX Wireless Buttons

Accepted Answer

Use the supplied tool to remove the back cover of the LRA-PBTX push button. Replace the battery with a fresh CR2032 lithium coin cell, following the polarity markings. Secure the cover and press the button to confirm the paired receiver responds. Keep loose coin cells away from children.

Question 28

How to Mount the SS-STROBE

Accepted Answer

To wall-mount the Safeguard Supply SS-STROBE, attach one mounting plate to the back of the strobe and fasten the other plate to the wall. Choose a location where people can see the flash from their usual work positions. After mounting, trigger the paired receiver to check visibility.

Question 29

ERA-DSTX Driveway Sensor Troubleshooting Guide: Fix Detection Issues

Accepted Answer

If an ERA-DSTX misses vehicles, check whether the vehicle passes through the sensor’s detection zone and whether the receiver can hear the signal from that location. Check the sensor angle, detection settings, battery, and reset interval. Test with a vehicle after each adjustment so you can identify what fixed the problem.

Question 30

LRA Help Hub

Accepted Answer

Centralized help desk page for the LRA series of products by Safeguard Supply, gathering programming guides, manuals, and demonstration videos.

Question 31

ERA Help Hub

Accepted Answer

Resource hub for ERA wireless alert system products, including programming guides, user manuals, troubleshooting articles, and video tutorials.

Question 32

Consolidated List of ERA Series Product Manuals

Accepted Answer

A consolidated list of ERA series product manuals and documentation. Use the FAQ index to find programming guides for each receiver, transmitter, and sensor.

Question 33

How to Program Your ERA-DCRX with ERA-UTX and ERA-PBTX Transmitters

Accepted Answer

Complete instructions for programming your ERA-DCRX desktop receiver with ERA-UTX and ERA-PBTX transmitters. This guide covers system components, pairing steps, customization options, and troubleshooting.

Question 34

Programming Guide: ERA-DCKIT with Additional ERA-UTX Transmitter

Accepted Answer

Complete guide for programming your ERA-DCKIT wireless doorbell system and adding an ERA-UTX transmitter.

Question 35

Programming the ERA-VPRX Portable Doorbell Receiver to 3 ERA Transmitters

Accepted Answer

To pair ERA transmitters with the ERA-VPRX portable receiver, unlock the controls and enter Code Learning mode. Select a zone, choose its melody, then trigger the transmitter and confirm the receiver acknowledges it. Repeat for each transmitter and test the alerts from the locations where you’ll use them.

Question 36

How to Extend the Range of the ERA-DCRX by Up to 4,000 Ft

Accepted Answer

Use the ERA-EXTX to add up to 4,000 additional feet of coverage by creating a signal relay between two ERA-DCRX receivers.

Question 37

What Is a Wired Doorbell Transformer?

Accepted Answer

Explanation of doorbell transformers, their location, function, and how to choose the right one for your wired doorbell system.

Question 38

Finding the User Manual

Accepted Answer

Where to find user manuals across the Safeguard Supply lineup. Each product page hosts the latest PDF manual for that SKU.

Question 39

Can I Use a Wired Push Button with a Wireless Chime Receiver?

Accepted Answer

Two methods to use wired doorbell push buttons with wireless door chime receivers: door chime extenders and ERA-UTX universal transmitters.

Question 40

Can Two Push Buttons Play Different Sounds on a Wireless Chime Receiver?

Accepted Answer

Most modern wireless doorbell systems support multiple push buttons with distinct sounds. This guide explains how different manufacturers implement this feature and how to set it up.

Question 41

Does Removing Batteries Delete the Programming?

Accepted Answer

Replacing batteries in a Safeguard Supply SS Series transmitter keeps its existing programming. The transmitter stores its settings in memory that retains them without battery power. Install the battery type specified for your model, follow the polarity markings, then trigger the transmitter to confirm the receiver still responds.

Question 42

How to Program the WC180-SS Wireless Doorbell Kit User Manual

Accepted Answer

Instructions for programming the WC180-SS wireless doorbell kit, including pairing transmitters to receivers and setting ringtones.

Question 43

How to Wire a Push Button to the ERA-UTX Universal Transmitter

Accepted Answer

To use a standard non-lighted wired push button with an ERA-UTX transmitter, connect the button’s two wires to the NO and COM terminals. Pressing the button then sends a wireless alert to a paired ERA receiver. Test the button and receiver together before securing the wiring and mounting the transmitter.

Question 44

Programming Guide: SS Series Wireless Alert System Components

Accepted Answer

Step-by-step instructions for programming SS Series wireless alert system components, including transmitters and receivers.

Question 45

Types of Outdoor Driveway Alarm Sensors and Driveway Monitor Sensors

Accepted Answer

Choose a passive infrared driveway sensor when you want alerts for people as well as vehicles. Use a magnetic probe or a pneumatic hose when the goal is vehicle detection. Choose a break-beam pair when you can place and align units on both sides of the crossing.

Question 46

Additional Programming Tips for the LRA-DCRXS

Accepted Answer

The red LED in the strobe lens area indicates zone status during programming. Each zone can only have one transmitter paired, and LED behavior reveals whether zones are open or occupied.

Question 47

How Many ERA Receivers Can Connect to a Transmitter/Sensor?

Accepted Answer

The ERA system supports multiple receivers per transmitter, so alerts can be placed in the areas where staff need to hear or see them.

Question 48

How Many Push Buttons/Receivers Can I Use with the WC180-SS?

Accepted Answer

System capabilities for the 2024 WC180-SS model supporting up to 58 transmitters, versus legacy pre-2024 constraints of 3 transmitters per receiver with up to 4 receivers per push button.

Question 49

How Many Transmitters Can I Connect to a ERA Receiver?

Accepted Answer

The ERA system supports up to 12 transmitters across its receiver models, with the ERA-DCRX using zone-based configuration and the ERA-RXPG offering individual melody assignment.

Question 50

How to Identify Low Battery in ERA Transmitters and Sensors

Accepted Answer

On an ERA-DCRX receiver, a zone light that keeps blinking for 10 minutes and a melody that plays twice indicate a low transmitter battery. Use the blinking zone to identify the affected transmitter, check its manual for the correct battery type, and trigger it again after replacing the battery.

Question 51

How to Program a Push Button or Sensor to the LRA-DCRXS

Accepted Answer

Instructions for programming an LRA transmitter/sensor to the LRA-DCRXS Receiver, which has two zones. Each zone can be assigned a different melody for identification.

Question 52

No Sound Coming From the LRA-DCRX or LRA-DCRXS Chime Receiver

Accepted Answer

There are three available LRA receivers: the LRA-DCRX, LRA-DCRXS, and LRA-VPRX. Check that sound mode is enabled and volume is properly adjusted.

Question 53

Programming & Tips for the LRA-C1000 (LRA-DCTX)

Accepted Answer

The LRA-C1000 is a long-range entry alert system designed for businesses, shops, warehouses, and larger homes with a transmitter and receiver that communicates up to 1,000 ft.

Question 54

Programming Problems with the LRA-DCRXS — Solid LED Light

Accepted Answer

A solid red LED on the LRA-DCRXS receiver indicates that both zones are already programmed with transmitters. To add new transmitters, the receiver memory must be deleted first.

Question 55

Solutions When You Can't Hear Your Doorbell: Complete Guide

Accepted Answer

This guide explores effective solutions for poor doorbell coverage, focusing on wireless alternatives and doorbell extenders that provide maximum coverage throughout your home.

Question 56

Using 12V DC Devices with the ERA-DCRX 12V Outputs

Accepted Answer

Use an ERA-DCRX zone’s 12V DC output to power a compatible alert accessory when that zone activates. Check the accessory’s current requirements and polarity before connecting it. If the accessory needs a separate power supply, check whether the receiver’s C-FORM relay and the accessory’s wiring are compatible.

Question 57

Using the C-Form Relay on the ERA-DCRX Receiver

Accepted Answer

The ERA-DCRX receiver's C-Form relay can connect external devices that need separate power or control beyond the standard 12V DC outputs.

Question 58

What Are the 12V Outputs on the ERA Receiver Used For?

Accepted Answer

The ERA-DCRX receiver's integrated 12V DC outputs support zone-specific alert accessories such as LED strobes and 105 dB sirens.

Question 59

Why Use Different Sounds for Each Zone in Your ERA Alert System

Accepted Answer

Set up distinct alert sounds for different zones in your ERA wireless alert system. Improve response time with instant entrance identification.

Question 60

Wire an External Device to the Relays on the LRA-DCRX

Accepted Answer

The LRA-DCRX relay can switch a compatible external device, such as a strobe, when the receiver activates. Check the relay ratings and the accessory’s wiring and power requirements before connecting it. Use the receiver manual to identify the terminals and confirm how the accessory should receive power.

Question 61

How to Change the Melody on the LRA-DCRXS Receiver

Accepted Answer

Change melodies on an LRA-DCRXS receiver that is already programmed to LRA transmitters. Different melodies can be assigned to different zones so users know which door triggered the receiver.

Question 62

How to Delete Programming Memory from a LRA Receiver

Accepted Answer

Each zone on an LRA receiver accommodates only one transmitter. Programming problems can often be resolved by deleting the receiver's memory and reprogramming.

Question 63

LRA Series Compatibility Notice

Accepted Answer

The LRA series products were upgraded in 2021 with control board changes. Compatibility considerations apply only to systems purchased before 3/01/2021.

Question 64

Program a LRA Transmitter to the LRA-DCRX Receiver

Accepted Answer

This guide walks through programming a transmitter to an LRA-DCRX receiver. The functionality remains the same despite style changes in the LRA-D1000 product line.

FAQ & Documentation

LRA Products

ERA Products

SS Series

Wireless Products

Driveway Alarms

Door Chime Extenders

Accessories

User Manuals

Powering Your Safeguard Supply Receiver at Home or Abroad

Product User Manual: LRA-D1000S-L Doorbell Kit

RED LED Indicator Lights on the LRA-DCRXS Plug-In Receiver

How to Replace the Battery in the LRA-PBTX Wireless Buttons

LRA Help Hub

Can Two Push Buttons Play Different Sounds on a Wireless Chime Receiver?

Does Removing Batteries Delete the Programming?

Additional Programming Tips for the LRA-DCRXS

How to Program a Push Button or Sensor to the LRA-DCRXS

No Sound Coming From the LRA-DCRX or LRA-DCRXS Chime Receiver

Programming & Tips for the LRA-C1000 (LRA-DCTX)

Programming Problems with the LRA-DCRXS — Solid LED Light

Solutions When You Can't Hear Your Doorbell: Complete Guide

Why Use Different Sounds for Each Zone in Your ERA Alert System

Wire an External Device to the Relays on the LRA-DCRX

How to Change the Melody on the LRA-DCRXS Receiver

How to Delete Programming Memory from a LRA Receiver

LRA Series Compatibility Notice

Program a LRA Transmitter to the LRA-DCRX Receiver

ERA-DCRX 12V Output Wiring: Wire Distance & Multiple Strobes

Powering Your Safeguard Supply Receiver at Home or Abroad

What is the ERA-UTDCR Wireless Door Alert System?

Extending ERA System Range Using Signal Relay Technology

ERA-PBTX Push Button User Manual

ERA-RXPG Plugin Receiver User Manual

Programming Guide: How to Set Up ERA-PIR Motion Sensor with ERA-DCRX Receiver

ERA-DCKIT Wireless Doorbell Kit User Manual

Connect DB-2000 Bell to ERA-DCRX Receiver for Enhanced Alert Volume

How to Clear Event Logs on Your ERA-VPRX Receiver

WDK-ERA-STROBE: Professional Wireless Alert System with Visual Notification

ERA-UTX Installation Guide: Push Button and Door Contact Mounting Instructions

How to Mount the SS-STROBE

ERA-DSTX Driveway Sensor Troubleshooting Guide: Fix Detection Issues

ERA Help Hub

Consolidated List of ERA Series Product Manuals

How to Program Your ERA-DCRX with ERA-UTX and ERA-PBTX Transmitters

Programming Guide: ERA-DCKIT with Additional ERA-UTX Transmitter

Programming the ERA-VPRX Portable Doorbell Receiver to 3 ERA Transmitters

How to Extend the Range of the ERA-DCRX by Up to 4,000 Ft

Can Two Push Buttons Play Different Sounds on a Wireless Chime Receiver?

Does Removing Batteries Delete the Programming?

How to Wire a Push Button to the ERA-UTX Universal Transmitter

How Many ERA Receivers Can Connect to a Transmitter/Sensor?

How Many Transmitters Can I Connect to a ERA Receiver?

How to Identify Low Battery in ERA Transmitters and Sensors

Solutions When You Can't Hear Your Doorbell: Complete Guide

Using 12V DC Devices with the ERA-DCRX 12V Outputs

Using the C-Form Relay on the ERA-DCRX Receiver

What Are the 12V Outputs on the ERA Receiver Used For?

Why Use Different Sounds for Each Zone in Your ERA Alert System

Programming the SS130 Door Alert Kit by Safeguard Supply

Does Removing Batteries Delete the Programming?

How to Program the WC180-SS Wireless Doorbell Kit User Manual

Programming Guide: SS Series Wireless Alert System Components

How Many Push Buttons/Receivers Can I Use with the WC180-SS?

Can I Use a Wired Push Button with a Wireless Chime Receiver?

Can Two Push Buttons Play Different Sounds on a Wireless Chime Receiver?

Does Removing Batteries Delete the Programming?

Programming Guide: SS Series Wireless Alert System Components

ERA-DSTX Driveway Sensor Troubleshooting Guide: Fix Detection Issues

Types of Outdoor Driveway Alarm Sensors and Driveway Monitor Sensors

Doorbell Wire Extender: Hear a Wired Doorbell Farther Away

What is a doorbell wire extension kit?

How to Extend a Wired Doorbell Chime or Button Wire

How to Wire Two Door Chimes to One Doorbell Transformer: Complete Guide

Can I Use a Wired Push Button with a Wireless Chime Receiver?

Solutions When You Can't Hear Your Doorbell: Complete Guide

ERA-DCRX 12V Output Wiring: Wire Distance & Multiple Strobes

How to Install a Wired Doorbell

How to Install a Wired Doorbell Button

How to Replace a Wired Doorbell Push Button